Now We can access Petroleum Community by domain www.petrolcom.net______________ website new domain www.petrolcom.net
Page 1 of 3 1 2 3 LastLast
Results 1 to 12 of 32

Thread: ASME Flange Design Calculations

  1. #1

    Join Date
    May 2009
    Posts
    547
    Blog Entries
    1
    Thanks
    6
    Thanked 414 Times in 163 Posts

    ASME Flange Design Calculations

    The following link is very interesting to proceed an ASME design calculations for non-standard flanges:

    [This link Point to another website Only registered and activated users can see links.]
    Also* the following link is used for design of ASME non-standard blind flanges: ..................................

    [This link Point to another website Only registered and activated users can see links.]
    Note. The rating/class of standard flange can be easily found from ASME B16.5 or ASME B16.47 just by defining the flange material and knowing the design conditions (pressure & temperature)* and just defining the class or rate of the flange* you can find all the dimensions from the related ASME codes (ASME B16.5 or ASME B16.47). And in this case* no need to proceed a flange design calculations as prescribed for non-standard flanges. See the following site to find the max. design pressure of a flange as per ASME B16.5: .................................................. .................................................. .............

    [This link Point to another website Only registered and activated users can see links.]



    To recognize the definition of flange class or rating per ASME code* see the the following link: ............

    [This link Point to another website Only registered and activated users can see links.]

    Last edited by Abdel Halim Galala; 09-03-2009 at 02:34 PM.

  • # ADS
    Spons Circuit advertisement
    Join Date
    Always
    Posts
    Many
     
  • #2

    Join Date
    Oct 2007
    Posts
    85
    Thanks
    2
    Thanked 3 Times in 1 Post
    Thank you Abdel Halim.

  •    Sponsored Links



    -

  • #3

    Join Date
    Dec 2008
    Posts
    5
    Thanks
    1
    Thanked 1 Time in 1 Post
    thanks so much ...

  • #4

    Join Date
    Feb 2008
    Posts
    199
    Thanks
    0
    Thanked 6 Times in 6 Posts
    Hi Mr Galala
    Can you please share the spreadsheets of the above calculations ?

    Thanks in advance
    Praphulla.dp@gmail.com
    Praphulla

  • #5

    Join Date
    Sep 2008
    Posts
    236
    Thanks
    0
    Thanked 3 Times in 3 Posts
    thanks

  • #6

    Join Date
    Jul 2009
    Posts
    40
    Thanks
    65
    Thanked 4 Times in 2 Posts
    I imitate the calculation sheet from the website (

    [This link Point to another website Only registered and activated users can see links.]
    Try it* and your any comments is welcome.

    Flange Rating_(NPS 0.5~24)_V3.0.xls Based on ASME B16.5 2009

    [This link Point to another website Only registered and activated users can see links.]
    Flange Rating_Large Diameter_(NPS 26~60)_V1.0.xls Based on ASME B16.47 2006

    [This link Point to another website Only registered and activated users can see links.]


  • #7

    Join Date
    May 2009
    Posts
    2,312
    Blog Entries
    1
    Thanks
    1
    Thanked 506 Times in 175 Posts
    thanks Abdel Halim Galala and ccpjeff
    بسم الله الذي لا يضر مع إسمه شئ فى الأرض ولا في السماء
    Muhammad Khurram

  • #8

    Join Date
    Jan 2009
    Posts
    187
    Thanks
    0
    Thanked 24 Times in 12 Posts
    Lot of thankx to "Abdel Halim Galala" & "ccpjeff"

  • #9

    Join Date
    Aug 2009
    Posts
    56
    Thanks
    0
    Thanked 17 Times in 4 Posts
    many thanks sir

  • #10

    Join Date
    Sep 2008
    Posts
    28
    Thanks
    0
    Thanked 3 Times in 1 Post
    well i m a mechanical engineer and involved in work static equipment designing-pressure vessel* heat xchanger* column* tower* i have to check the GA 7 fabrication drawings for these .can any body help me how to improve on this any reference book* document regarding these drawings* specific points to be considered while checking drawing

  • #11

    Join Date
    Oct 2009
    Location
    Indonesia
    Posts
    81
    Thanks
    0
    Thanked 6 Times in 4 Posts
    thanks for sharing...

  • #12

    Join Date
    Apr 2010
    Location
    Indonesia
    Posts
    8
    Thanks
    0
    Thanked 1 Time in 1 Post
    thanks for your kind to share to newbie like me :-)

    Regards*

    M. Taufik
    Junior Mechanical Engineer

    •   

    Similar Threads

    1. ASME Flange Design Calculations
      By Abdel Halim Galala in forum Engineering Spreadsheets & Presentations
      Replies: 47
      Last Post: 09-29-2017, 07:04 PM
    2. Shell and Tube Heat Exchanger Mechanical Design Calculations per ASME & TEMA
      By Abdel Halim Galala in forum Mechanical Engineering
      Replies: 24
      Last Post: 05-05-2017, 01:48 PM
    3. Pressure Vessel Design Calculations as per ASME BPVC - Section VIII* Division 1
      By Abdel Halim Galala in forum Mechanical Engineering
      Replies: 24
      Last Post: 08-19-2015, 06:44 AM
    4. Replies: 2
      Last Post: 08-28-2013, 09:42 AM
    5. Query on Flange Design as per ASME Section VIII* Div.1* App 2
      By hssimha in forum Mechanical Engineering
      Replies: 0
      Last Post: 03-13-2012, 11:10 AM

    Tags for this Thread

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •